Uimp = 4 kV
Un = 400 V
Ui = 400 V
≤ Up = 2,5 kV
II
InC = 16 ANot: IB değerlerinin toplamı, InA değerini aşmamalıdır.
| Koşullu nominal kısa devre akımı | Maks. ön sigorta / Icc'yi tamamlayıcı karakteristikler |
|---|---|
| Icc = 10 kA | maks. 63 A gG |
InA = 32 A
2
fn = 50 Hz
Evet
RDF = 1
2
| Cihaz sayısı | Tip (montaj cihazı için) | Anzahl der Pole (vom Einbaugerät) | Karakteristik (montaj cihazının) | Nominal akım (montaj cihazının) | Nominal kısa devre akımı (montaj cihazının) | Nominal kaçak akım I_Δn (montaj cihazının) |
|---|---|---|---|---|---|---|
| Kaçak akım devre kesicisi (RCCB) | Tip A | 30mA | ||||
| Minyatür devre kesici | 3 | C | 20A |
| Klemens noktası başına maksimum iletken sayısı | İletken kesiti minimum. | İletken kesiti maks. | İletken kesiti | İletken Şekli | İletken malzemesi |
|---|---|---|---|---|---|
| 1 | 1.5 mm² | 16 mm² | yüksüklü ince telli | yuvarlak | Cu |
| 1 | 2.5 mm² | 16 mm² | tek telli, çok telli | yuvarlak | Cu |
| Klemens noktası başına maksimum iletken sayısı | İletken kesiti minimum. | İletken kesiti maks. | İletken kesiti | İletken Şekli | İletken malzemesi |
|---|---|---|---|---|---|
| 1 | 2.5 mm² | 10 mm² | tek telli, çok telli, yüksüklü ince telli | yuvarlak | Cu |
Kapak
Evet
12 modül
3
IP65
IK08
Hayır
Genişletme Kümesi
Korunaklı tesisat
35 °C
-5 °C ila +40 °C
40 °C’de ≤ %50, 25 °C’de ≤ %100
Polistiren
750 °C
V-2
Evet
583 mm
295 mm
129 mm
6,61 kg
Gri, RAL'a benzer 7035
DIN EN IEC 61439-7, DIN EN IEC 61439-3
65000086
4012591186489
1
85371098
DYNAMIC: EC004474 - Control cabinet for the utility sector
ETIM-9.0: EC004474 - Control cabinet for the utility sector
ETIM-8.0: EC004474 - Control cabinet for the utility sector
ETIM-7.0: -
ETIM-6.0: -
ETIM-5.0: -
ETIM-4.0: -
Ready-for-connection, encapsulated low-voltage switchgear combination in box design for charging stations for electric vehicles (AEVCS) according to DIN EN IEC 61439-7 in protection class II to be supplied. To ensure a maximum degree of safety and availability of the energy switchgear assembly, the design of the switchgear must comply with the requirements of DIN EN IEC 61439-7 for all built-in components. The switchgear assembly is supplied by an outlet from an upstream power distribution. To prevent stray currents, the main busbar system must be constructed as an EMC-compliant 5-conductor system according to DIN VDE 0100-100. The conductors of the busbar system must be labeled with L1 - L2 - L3 - N - PE in accordance with DIN EN 60446 (VDE 0198). The neutral busbar must be installed close to the outer conductors and throughout its route insulated from all conductive parts to ensure EMC compliance. The neutral busbar must have the same current-carrying capacity as the outer conductors. The following data applies to the feed-in: Rated voltage [Ue]: 400 V, rated frequency [fn]: 50 Hz, network system: TN system, upstream protective device [In]: ≤ 63 A, undisturbed short-circuit current on site [Icp]: 50 kA, overvoltage category: III, connection of supply line: from below via , cross-section: ... x .....mm² , connection to the load disconnect switch.
Article: charging distributor KV EV 11kW 2101 https://www.hensel-electric.de/en-en/produkt/28856/KV-EV-11kW-2101